Nissan Primera

1990-1992 of release

Repair and car operation



Nissan Primera
+ Nissan Primera brand Cars
- Current leaving and service
   - Schedule of routine maintenance
      Introduction
      Current leaving
      General information on control
      Check of levels of liquids
      Check of a condition of tires and pressure in them
      Replacement of impellent oil and oil filter
      Check of level of liquid of system of hydrostrengthening of a wheel
      Check of level of liquid of automatic transmission
      Rotation of wheels
      Check of a condition and replacement of hoses of an impellent compartment
      Condition check, adjustment of a tension and replacement of driving belts
      Check and adjustment of turns of idling of the engine and level WITH
      Check of a condition of the battery, care of it and charging
      Check and replacement of spark plugs
      Check and replacement of candle VV of wires, covers and distributor begunka
      Check of level of oil in a manual box of gear shifting
      Check and adjustment of gaps of valves
      Check and greasing of draft of a drive of a butterfly valve
      Replacement of an element of the air filter
      Check of fuel system
      Check of functioning of system of cooling
      Check of a condition of system of production of the fulfilled gases
      Check of a condition of components of a suspension bracket and steering
      Check of a condition of protective covers of power shafts
      Check of brake system
      Check of a condition and replacement of brushes of screen wipers
      Replacement of transmission liquid
      Plums, washing and filling of system of cooling
      Replacement of the fuel filter
      Replacement of transmission oil of manual transmission
+ Engine
+ cooling and heating Systems
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Manual transmission, differential and main transfer
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Appendices



Condition check, adjustment of a tension and replacement of driving belts

Two times year or each 10000 km of run (that will come earlier)

Condition check

The driving belts sometimes called by belts V - figurative section are in a forward part of the engine and play important role in operation of the car and its separate components. Because of features of a material and operating conditions driving belts fail after a while, and consequently their condition it is necessary to check and regulate periodically effort of a tension in order to avoid serious damages of the engine.

The quantity of the belts used on the concrete car, depends on the units established on it and systems. Driving belts are applied to actuating of the generator, the steering pump, the water pump and the compressor of central air of air. Depending on an arrangement of pulleys one belt can put in action at once some components. On an illustration the arrangement of belts of the injector engine is represented, on an illustration is shown, how both belts of the carburetor engine if the amplifier of a steering (servoupravleniye) is established are laid. If the amplifier is not established, only one belt is applied. If the conditioner represented on an illustration is established, the belt between the generator and the crankshaft puts in action also the compressor. If a belt прожимается more than it is set, it is necessary to carry out adjustment.

Arrangement of driving belts on the injector engine. To check a tension on the places designated by shooters

1 — a remenny pulley of the water pump
2 — a remenny pulley of the pump of the steering amplifier
3 — a remenny pulley of the generator
4 — a remenny pulley of the crankshaft

Arrangement of driving belts on the carburetor engine with the amplifier of a steering. To check a tension in the places designated by shooters

1 — a remenny pulley of the generator
2 — a remenny pulley of the water pump
3 — a belt pulley of the pump of the steering amplifier
4 — a belt pulley of the crankshaft

 PERFORMANCE ORDER

  1. Switch off the engine, open a cowl and find various driving belts in a forward part of the engine. Check a belt tension only on the cold engine. If the engine hot before check of a tension there have to pass at least 30 minutes.

Some of most often meeting defects of driving belts (check a condition of belts very carefully in order to avoid their premature gap).

  1. Fingers (and using a small lamp if it is necessary) walk on all length of each belt, feeling them on existence of cracks and stratifications. Also check, whether is not present on belts of attritions and zapolirovanny sites to shine. Each belt should be examined from both parties that means need of its perekruchivaniye for check of a condition of seamy side.
  2. The tension of a belt is checked by strong pressing on it by a thumb and definitions of degree of its deflection. The tension of a belt is checked in designated by an arrow on an illustration a place in the middle between pulleys. Size of a deflection measure by a ruler. The rule of a thumb says that if the distance between centers pulleys makes from 180 to 280 mm, the size of a deflection should equal 6 mm. If the distance between centers pulleys is in limits between 300 and 400 mm, the deflection should be 13 mm. If the tension differs from given in Specifications, make adjustment.
Measurement of size of a deflection of a driving belt by means of a ruler and a planeness measuring instrument.
  1. Make sure that the ruler is perpendicular to a planeness measuring instrument

Adjustment

In need of adjustment of a tension of a belt towards its increase or reduction it becomes a natyazhitel. Though the arrangement of belts differs, adjustment is carried out in the same way. Weaken a lock bolt sideways a natyazhitel and turn the corresponding adjusting bolt while the tension will not correspond to demanded value. Again tighten a bolt and check a tension.

Replacement

For replacement of a belt follow the instructions provided above on adjustment, but thus remove a belt from pulleys.

In certain cases you should remove more than one belt because of features of their arrangement in a forward part of the engine. Therefore, and also because belts tends to fail at the same time, to replace them too best of all at the same time. Mark each belt and a flute corresponding to it on a pulley correctly to establish new belts.

Upon purchase of new belts it is convenient to take with itself old to have possibility directly to compare them on length, width and a design.

Check a tension of new belts after run of several hundred kilometers.